OmniTurn mmmmmmmmmmmmm Made in Oregon!
Fast... Precise... Affordable...

OmniTurn GT-75
  • Gang-Tooled slant bed
  • 5hp spindle w/5C nose
  • Air-actuated collet closer
  • Flood-coolant system
  • Spindle Positioning Option

Gang-tooled for fastest tool changes.
75° slant-bed lets chips fall away quickly.
12” X-Axis travel; 9” Z-Axis travel.
Highest quality ground ball-screws and linear guides for precision and reliabilty.
Closed-loop servo system provides .0001” accuracy with .00005” resolution.
5hp spindle (C-Axis positioning optional)
4000rpm (5000 rpm optional)
Barfeed ready.
     

OmniTurn GT-Jr Turning Center
Fast... Precise... Affordable...


Gang Tooling is fast!

Gang-tooling is fast ! Tool to tool in less than 1/2 second.

Gang-tooling is fast for repeat setups! OmniTurn’s “Save Offsets” feature lets you setup a complex repeat job in just minutes if you’ve saved your tooling in this 805PFB holder. Just re-locate the holder on the tooling plate and load your part program with offsets and you’re ready to run parts in minutes. No need to re-set all your tooling. The locating pin insures that the holder is back in place, and the original offsets load into the OmniTurn with the program.

OmniTurn 805 Bar

The OmniTurn 805PFB (pictured above) is an 8-station tool-bar that accepts 5/8” tooling on 1.1” centers. Stop-pin fits either end so bar can be located on either side of OmniTurn tooling plate. OmniTurn “Save Offsets” feature instantly retrieves offsets when program is loaded, so repeat jobs can be re-set in minutes. Shown at right on OmniTurn GT table note that steep 75° angle allows chips to fall away quickly into chip-pan. $195.

OmniTurn GT-Jr Dimensions
Specifications:

Capacities
   Workholding . . . . . . . . . . . . . . . . . . . . . . . . 5C Collet
. . . . . . . . . . . . . . . . . . . . . . . . . . . 4” Chuck Max (opt.)
  Max. Cutting Diameter . . . . . . . . . . . . . . . . . . . . . .6”
  Max. Bar Diameter . . . . . . . . . . . . . . . . . . . . . . 1.06”
  Tooling Plate . . . . . . . . . . . . 6” x 14” with 3/8” T-Slot

Spindle
  Max Speed . . . . . . . . . . . . . . . . 4,000rpm (5000 opt.)
  Max Rating . . . . . . . . . . . . .. . . . . . . . . . . . . . . . .5 hp
  Spindle Nose . . . . . . . . . . . . . .. . . . 5C w/4° camlock
  Drawtube Bore . . . . . . . . . .. . . . . . . . . . . . . . .1.125”

Construction
  Ways . . . . . . . . . . . . . . . . . Precision Linear Guides
  Ball Screws . . . . . . Precision-ground, Zero Backlash
  Base Billet . . . . . . . . . . . . . . MJ7 Composite Casting
  Headstock . . . . . . . . . . . . . . . . . . . . . . . . . Mehanite
  Coolant Pump . . . . . 1/8hp 5gpm (1/4hp 20gpm opt.)

Travels & Feedrates
   X-Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12”
  Z-Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9”
  Resolution of Slide Travel . . . . . . . . . . . . . . 0.00005”
  Repeatability of Slide Travel . . . . . . . . . . . . . 0.0001”
  Threading . . . . . . . . . . . . . . 240tpi to 0.5tpi (2”pitch)
  Axes Thrust . . . . . . . . . . . . . . 500lbs cont. 750lbs int.
  Max Rapid . . . . . . . . . . . . . . . . . . . . . . . . . . . 300ipm
  Max Cutting .. . . . . . . . . . . . . . . . . . . . . . .. . . 300ipm

OmniTurn
(541) 332-7004
(541) 332-1018 fax
email

Back to Top

OmniTurn Technical Specifications Technical Specifications

OmniTurn GT-Jr Lathe Download Flyer (PDF)

OmniTurn GT-Jr Pricing For pricing information

[ Home ] [ GT-75.htm ] [ GT-Jr ] [ Attachments ] [ CNC Control ] [ Custom X-Z Slides ] [ Repair Parts ] [ Rebuilding your OmniTurn ]
[ Used OmniTurns ] [ Contact Us ] [ OmniTurn ZipLoader ] [ Repair Catalog (PDF) ]